|
 | Vetus Water Temperature Gauges Can be supplied for 12 or 24 Volt D.C. Scale calibration: 40-120º C and 105-250ºF.
Temperature sensors are available as optional equipment. |
|
|
|
|
|
 | Vetus Revolution Counters, with Hour Counter incorporated Revolution Counter (with hour counter incorporated)
12/24 Volt D.C., suitable for alternators with W-connection.
Suited for diesel engines.
Scale calibration: 0-4000 r.p.m. |
|
|
|
 | Vetus Hour Counters REVOLUTION COUNTER (WITH HOUR COUNTER INCORPORATED)
12/24 Volt D.C., suitable for alternators with W-connection. Suited for diesel engines. Scale
calibration: 0-4000 r.p.m. |
|
|
|
 | Vetus Voltmeters Can be supplied for 12 or 24 Volt D.C. Scale calibration respectively: 10-16 V and 20-32 V. |
|
|
|
|
|
 | Vetus Ammeter Scale calibration: +/- 60 Amp., for 12 or 24 Volt D.C., with shunt incorporated. |
|
|
|
|
 | Vetus Oil Pressure Gauges Available for 12 or 24 Volt D.C. Scale calibration: 0-8 kg/cm2 and 0-110 p.s.i. Oil pressure sensors are available as optional equipment. |
|
|
|
 | Vetus Rudder Position Indicator Both indicating units have scale illumination and are suitable for both 12 V and 24 V electrical
installations. An indicating unit may also be connected to the rudder position sensor of the VETUS automatic pilot, type AP2S. In this case, the sending unit, type RFU 1718, need NOT be installed. |
|
|
|
|
|
 | Vetus Water Level Indicators Available for 12 or 24 Volt D.C. |
|
|
|
|
|
 | Vetus Fuel Level Indications Available for 12 or 24 Volt D.C. |
|
|
|
|
|
 | Vetus Exhaust Temperature Alarms Designed for water injected exhaust systems. Provides a visual and an audible alarm when the temperature inside the exhaust hose or the muffler exceeds an acceptable level. The temperature sensors, to be fitted into the exhaust hose or the waterlock/ muffler, and the alarm unit must be ordered separately. In the case of a twin engine installation 2 sensors may be connected to 1 alarm unit, if so required. One sensor may also serve two alarm units, e.g. in the case of a second steering position. Available for 12 and 24 Volt D.C. |
|
|
|
|
|
|
|
|
 | VETUS ENERGY CONSUMPTION GAUGE 12/24 VOLT, WITH 200 AMP SHUNT. 158MSCBMON
It is often very important to know the exact state of charge of a battery or battery bank. Measuring only the voltage and current at a certain moment, by means of a voltmeter and ammeter respectively, does not provide sufficient information to ascertain the actual charge level. The VETUS energy consumption gauge continuously monitors the voltage and the charge or discharge current and can indicate from this information the level of battery charge. Furthermore, if the battery bank is being discharged, it will calculate the remaining time before complete discharge is achieved.
The energy consumption gauge monitors the following functions:
- Voltage; scale range 0-32.6 Volts. An alarm warns of low voltage during discharge or excessive voltage during charging.
- Charge of discharge current; scale range +/- 200 Amps.
- Battery state of charge; scale range 0-99.9% of the nominal battery capacity. This capacity can be entered by the user.
- Time to complete discharge at the present discharge rate; scale range 0-999 hours.
The instrument can be used in both 12 Volt and 24 Volt electrical systems. It is supplied with a 200 A shunt and
both square and round bezels. Diameter of hole: ø 52 mm. Outside dimensions: Ø 62 mm
|
Price: £317.25 (Including: VAT) |
Qty: |
| |
| |
|
 | VETUS WIND SPEED AND WIND DIRECTION INDICATOR, TYPE WSD834, INCL. SENSOR #12/24 V 545WNDWSD834
This sensor may be connected to any type of wind instrument with a NMEA 0183 input.
• The instrument gives digital read-out of wind speed and both digital and analogue indication of wind direction.
• The wind speed indication can be displayed in metres/second, knots or Beaufort scale.
• Can display apparent or true (*) wind speed and wind direction
• Adjustable damping of wind speed and wind direction.
• Maximum wind speed experienced is retained in memory.
• Analogue wind direction can be set to show magnified close hauled reading 20° to 50°.
• Adjustable acoustic wind speed alarm
• Velocity Made Good (VMG*)
• Provided with adjustable scale illumination.
• Instrument dimensions: 110 x 110 x 57 mm (height).
• Built-in depth: 32 mm.
• The pane of the read-out instrument is covered with a scratch-free coating.
• Current consumption: 12 Volt – 140 mA (scale illumination: 20 mA) 24 Volt - 80 mA (scale illumination: 40 mA)
• Current supply is also possible via a mains voltage adaptor (110 or 230 Volt A.C.) to 12 volt D.C., with a minimum output of 250 mA. A suitable 230 Volt A.C. adapter may be supplied by VETUS
• The instrument comes complete with the solid state wind sensor, without moving parts, described below.
(*) The true wind speed and wind direction, as well as the “Velocity Made Good” can only be indicated if
boat speed data is input. The VETUS paddlewheel sensor SPD 002 can be used for this purpose.
This sensor may also be used to get accurate information on your PC or lap top about the wind speed and the
wind direction. The VETUS software is on CD-ROM and is easy to install on your computer. | Large Image
|
Price: £719.10 (Including: VAT) |
Qty: |
| |
| |
|
 | VETUS MASTHEAD SENSOR UNIT ONLY FOR WSD833/WSD834, #12/24 V 551ACCMMW004
A Wind sensor without moving parts. This combined sensor unit comes complete with 20 m of cable and a mounting bracket. Suitable for 12 Volt D.C.
This unique wind sensor measures both the wind speed and the wind direction with the aid of one single chip. Operation is based on the principle that a warm surface will cool down whenever there is a current of air around it. The more wind there is, the greater will be the cooling-down effect. | Large Image
|
Price: £481.75 (Including: VAT) |
Qty: |
| |
| |
|
 | VETUS CD-ROM FOR WSD833/WSD834, FOR PC OR LAPTOP 551ACCCD833
|
Price: £52.88 (Including: VAT) |
Qty: |
| |
| |
Vetus Rudder Position Indicators VETUS rudder position indicators provide, by means of electronics, a display of the rudder position on the indicating unit. They consist of a sending unit, complete with an adjustable transmission arm and ball joints, and one or two (dual steering position) read-out instruments.
The rudder position sensor type RFU1718 may be connected to up to two Vetus rudder position indicators. It is possible to connect two indicating units of different size.
The sending unit is suitable for both 12 V and 24 V electrical installation. The overall dimensions of the indicating unit, type 1700, are: 94 x 94 x 15 mm and the built-in depth is 30 mm. The instrument is provided with scale illumination and comes complete with connection
cable of 15 metres in length.Also this read-out instrument will suit both 12 V and 24 V electrical installations. The indicating unit may also be connected to the rudder position sensor of the VETUS automatic pilot, type AP2S. |
|
 | VETUS RUDDER POSITION SENSOR TYPE RFU1718 038SNDRFU1718
| Large Image
|
Price: £157.45 (Including: VAT) |
Qty: |
| |
| |
 | VETUS RUDDER POSITION INDICATOR TYPE RPI1700, 12/24 V (EXCL. SENSOR) 037GAURPI1700
| Large Image
|
Price: £264.38 (Including: VAT) |
Qty: |
| |
| |
Awaiting Images and information from manufacturer |
|
|
|
